Camouflaging a Dated Off-center Bathroom Lighting Fixture
by EYSpace in Living > Decorating
21005 Views, 53 Favorites, 0 Comments
Camouflaging a Dated Off-center Bathroom Lighting Fixture
![Lighting fixture before no watermark.jpg](/proxy/?url=https://content.instructables.com/FDD/6NP0/J2QF5CJ8/FDD6NP0J2QF5CJ8.jpg&filename=Lighting fixture before no watermark.jpg)
![Bathroom Lighting: Quick fix to update a dated bathroom vanity light](/proxy/?url=https://content.instructables.com/FV7/SP12/J2QF5AJ4/FV7SP12J2QF5AJ4.jpg&filename=Bathroom Lighting: Quick fix to update a dated bathroom vanity light)
![Lighting fixture before and after before after_edited-1.jpg](/proxy/?url=https://content.instructables.com/FBM/T03L/J2QF5ACL/FBMT03LJ2QF5ACL.jpg&filename=Lighting fixture before and after before after_edited-1.jpg)
I needed a quick inexpensive way to update a very dated bathroom lighting fixture in a bathroom without replacing it. Adding to the challenge was the fact that the fixture wasn’t centered over the vanity. My solution was to make a cover to hide the existing fixture - it cost less than $15 to make, and I didn’t have to use any power tools! You can watch the video of how I made it and here are the main steps.
Before:
![Old off-centered lighting fixture_edited-2.jpg](/proxy/?url=https://content.instructables.com/F9C/V1M4/J2QF5ADV/F9CV1M4J2QF5ADV.jpg&filename=Old off-centered lighting fixture_edited-2.jpg)
Here's what the fixture looked like before - very dated and off-center over the vanity.
Make the Wood Structure for the Cover
![Connecting the side to the front wood boards_edited-1.jpg](/proxy/?url=https://content.instructables.com/F1H/GLL7/J2QF5ABT/F1HGLL7J2QF5ABT.jpg&filename=Connecting the side to the front wood boards_edited-1.jpg)
![Gluing back dowel pieces_edited-1.jpg](/proxy/?url=https://content.instructables.com/FO0/2997/J2QF5ABW/FO02997J2QF5ABW.jpg&filename=Gluing back dowel pieces_edited-1.jpg)
What I used to make it:
1/4" x 6" poplar boards
3/4" thick square wood dowels
I cut the boards into 3 sections (2 x 4.5" and 1x18") and cut the dowels into 4 pieces (4 x 5.5"). I used wood glue to attach the square dowels to join the side to the front boards and I glued the other 2 dowel pieces to the back of the sides.
![Plaid products for finishing wood_edited-1.jpg](/proxy/?url=https://content.instructables.com/FOZ/N87D/J2QF5AEJ/FOZN87DJ2QF5AEJ.jpg&filename=Plaid products for finishing wood_edited-1.jpg)
![Finish for wood - waxing_edited-1.jpg](/proxy/?url=https://content.instructables.com/FMY/WSB8/J2QF5ABV/FMYWSB8J2QF5ABV.jpg&filename=Finish for wood - waxing_edited-1.jpg)
Here's what I used as a finish for the wood:
Chalk paint (sheepskin): http://amzn.to/2k8K5O6
Wood tint: http://amzn.to/2k8K5O6
White wax: http://amzn.to/2k8K5O6
I painted the wood with 2 coats of the paint, then brushed on a coat of the stain and then protected the surface with a coat of the white wax.
Step 1: Make Light Diffuser
![Gluing fabric to acrylic panel with mod podge_edited-2.jpg](/proxy/?url=https://content.instructables.com/FJH/FA20/J2QF5ACK/FJHFA20J2QF5ACK.jpg&filename=Gluing fabric to acrylic panel with mod podge_edited-2.jpg)
![Trimming off fabric from acrylic panel.jpg](/proxy/?url=https://content.instructables.com/FI4/DVLG/J2QF5AEK/FI4DVLGJ2QF5AEK.jpg&filename=Trimming off fabric from acrylic panel.jpg)
![Acrylic panel installed to the back of the lighting fixture cover_edited-1.jpg](/proxy/?url=https://content.instructables.com/FOD/CZJ3/J2QF5AAH/FODCZJ3J2QF5AAH.jpg&filename=Acrylic panel installed to the back of the lighting fixture cover_edited-1.jpg)
Here's what I used to make it:
Thin linen like fabric
Plexiglass (Acrylic) sheet for diffuser (11”x14” ⅛” thick): http://bit.ly/2krpq8
Mod Podge: http://bit.ly/2krpq8
I placed the fabric on top of the non-glare side of the acrylic panel and soaked it with MOD PODGE making sure the fabric is soaked through. I let it dry and then I trimmed off the excess along the edges with a utility knife. Then I glued it to the structure.
Installing the New Cover
![3m command strips to hang the new cover_edited-1.jpg](/proxy/?url=https://content.instructables.com/F8N/SNU3/J2QF5AAG/F8NSNU3J2QF5AAG.jpg&filename=3m command strips to hang the new cover_edited-1.jpg)
I removed the old cover and placed 3M command strips on either side of it to hang the new cover. It is very light so the strips are fine to hold it and this avoids having to make holes in the wall. You could also use brackets to attach it to the wall.
Attach the Light Cover
![Using phone level to install light.jpg](/proxy/?url=https://content.instructables.com/F50/I6SL/J2QF5AEM/F50I6SLJ2QF5AEM.jpg&filename=Using phone level to install light.jpg)
I used the level on my smart phone to help make sure the fixture was hung straight.
Center the New Cover
![Bottom view of new centered lighting fixture_edited-1.jpg](/proxy/?url=https://content.instructables.com/FY3/8181/J2QF5AB6/FY38181J2QF5AB6.jpg&filename=Bottom view of new centered lighting fixture_edited-1.jpg)
The new cover is centered over the vanity and covers up the existing light fixture completely.
After: Enjoy Your New Centered Light Fixture!
![new centered light fixture.jpg](/proxy/?url=https://content.instructables.com/FKD/ZDFU/J2QF5AD8/FKDZDFUJ2QF5AD8.jpg&filename=new centered light fixture.jpg)
![Before and after right side watermarked high res.jpg](/proxy/?url=https://content.instructables.com/FN3/FNBG/J2QF5COT/FN3FNBGJ2QF5COT.jpg&filename=Before and after right side watermarked high res.jpg)
![DIY small bathroom remodel: budget bathroom ideas](/proxy/?url=https://content.instructables.com/F3J/VEUO/J2QF5BR0/F3JVEUOJ2QF5BR0.jpg&filename=DIY small bathroom remodel: budget bathroom ideas)
When the light is on, there's no telling that the actual light fixture isn't centered! Not bad for $15!
This was only one of the things I did to upgrade this small bathroom and you can watch the rest of the makeover in the video!